TREASURE CONTAINER

0 (likes)
89 (views)
This product is available only if you have an account in My Mini Factory service
×
Color:

The container is printed and glued. 4 magnets with a diameter of 8 mm and a thickness of 3 mm are required. A steel axle with a diameter of 3 mm and a length of 40 mm is required. It can be up to 2 mm longer. I recommend using PATTEX – ONE FOR ALL CRYSTAL glue Parts can be sanded after printing. Supports only necessary when printing part 7 for the magnet sockets. Supports only on the printer table. Instructions attached showing how to glue. You can change colors. Decorative elements can be changed. To open the container, turn the top cover to the left and then lift it up. To close the container, turn the lid to the left so that the lock is in the extreme left position. Then close the cover and turn it clockwise to the extreme position. The magnets should be glued into parts 7 and 8 in such a way that when these parts are assembled, the magnets attract each other. The magnets will then keep the cover closed. I will protect against automatic or unintentional rotation of the cover to the left to the open position. Be careful not to lift the cover too hard to avoid breaking the hinge. When assembling the container and gluing it, be careful to glue parts 6 and 8 together in such a way that part 7 moves freely, but without much play. When gluing parts 6 and 8, you must first insert part 6 into part 7. When gluing part 4 to part 2, you can use a tool, for example a wooden strip, to push part 4 into position. The glue is easy to remove and clean. You should use a cloth, paper and cotton buds several times. To remove the glue with a clean cloth. The glue is also easily removed after drying. The glue also has the function of removing scratches on printed parts. Removes scratches to a large extent. Sometimes scratches are unnecessary and that is a nice feature of the glue. If the lid hinge axis is pressed in with difficulty, you can use a 3 mm diameter drill to align the holes in part 8 and part 2. This must be done carefully so as not to increase the diameter of the hole, otherwise there will be looseness and less precision when closing. The photos show part 2 before optimization. It is included in the files after optimization. PL Pojemnik wydrukowany i sklejany. Konieczne 4 magnesy średnicy 8 mm i grubości 3 mm. Konieczna oś stalowa o średnicy 3 mm i długości 40 mm. Może być do 2 mm dłuższa. Zalecam użycie kleju PATTEX – ONE FOR ALL CRYSTAL Części po wydrukowaniu można szlifować. Podpory konieczne tylko przy drukowaniu części 7 dla gniazd magnesów. Podpory tylko na stole drukarki. Załączona instrukcja pokazująca jak skleić. Można zmieniać kolory. Można zmieniać elementy ozdobne. Aby otworzyć pojemnik należy obrócić górną pokrywę w lewo, a następnie unieść do góry. Aby zamknąć pojemnik należy obrócić pokrywę w lewo, tak aby zamek ustawił się w lewym położeniu skrajnym. Następnie należy zamknąć pokrywę i obrócić ją w prawo do pozycji skrajnej. Magnesy należy wkleić w część 7 i 8 w taki sposób aby po złożeniu tych części magnesy się przyciągały. Wtedy magnesy będą utrzymywały pokrywę w pozycji zamkniętej. Będę chroniły przed samoczynnym lub niezamierzonym obrotem pokrywy w lewo do pozycji otwartej. Należy uważać aby nie podnosić pokrywy za mocno aby nie złamać zawiasu. Należy uważać podczas składania pojemnika i sklejania, aby części 6 i 8 skleić ze sobą w taki sposób aby część 7 poruszała się swobodnie, ale bez dużych luzów. Przy sklejaniu części 6 i 8 najpierw trzeba część 6 włożyć do części 7. Przy wklejaniu części 4 do części 2 można użyć przyrządu, na przykład drewnianej listewki aby dobić część 4 do swojej pozycji. Klej łatwo się usuwa i czyści. Należy kilkukrotnie użyć szmatki, papieru, wacików na patyczku. Tak aby usuwać klej czystym czyściwem. Klej łatwo się usuwa również po wyschnięciu. Klej dodatkowo ma funkcję usuwania zarysowań części drukowanych. Usuwa rysy w dużym stopniu. Czasem zrysowania są niepotrzebne i to jest fajna funkcja kleju. Jeśli oś zawiasu pokrywy wciska się z trudem, można użyć wiertła o średnicy 3 mm aby wyrównać otwory w części 8 i części 2. Trzeba to zrobić ostrożnia aby nie zwiększyć średnicy otworu, bo będą luzy i mniej precyzji przy zamykaniu. Na zdjęciach widoczna jest część 2 przed optymalizacją. W plikach załączona jest już po optymalizacji.

About the author:
adamwalczak
I have been dealing with technology from an early age. I am very happy with creating and solving difficult problems. I also deal with this topic professionally. I am a Specialist Mechanic and Electrician. I like to help. As a hobby, I develop other interests and combine various fields. Photography and graphics, RC modeling, automotive, shooting and military. Some of the graphics included in MyminiFactory can be purchased and downloaded in high definition from Adobe Stock for commercial use at the link: https://stock.adobe.com/pl/contributor/201480214/AWVW In 123RF you can download my other photos and graphics: https://pl.123rf.com/profile_awvw There are photos and graphics on various topics. I am open to various suggestions and ideas. I hope you enjoy my work and that it benefits you.

Reviews

This model have no reviews. Would you like to be the first to review? You need to print it first.