Body for TAMIYA DT03 chassis.

1 (likes)
515 (views)
This product is available only if you have an account in My Mini Factory service
×
Color:

A durable body designed by me for the TAMIYA DT03 chassis. The bodywork consists of many elements that fit together perfectly. To assemble the body, you need to use screws and nuts. To assemble the body, glue must be used in some places. To assemble some body elements, you need to make connections using a threaded rod and M3X8 sleeves. Installing the body on the TAMIYA DT03 chassis does not require destroying or modifying the original chassis. Only in one place you need to drill holes to a diameter of 3.1 mm. At this point, after this change, you will be able to use a screw and a nut instead of the screws from the original set. The biggest problem during design was finding the base points of the original chassis and reading the correct chassis curves. I didn't use any plans. I did not use any devices such as scanners. I only used a caliper and a ruler with millimeter divisions. During the design process, I printed some parts several times and tried them on, then made corrections. The design includes parts that may be attractive as separate elements. The rear spoiler is very cool and functional. It is also very durable. Parts that increase the stiffness of the original shock absorbers may also be useful. M3X25 screws are used in two places, here you can use, and this is even better, M3X26 screws, or measure and adjust/make the appropriate ones. This is because I wanted to test the model and I couldn't buy other screws. I tested the body using standard parts. TAMIYA basic brush motor. Basic regulator 60 A TAMIYA. Old type 27 MHz equipment. NiMH battery quite old 4000 mAh. I installed Carson wheels. I installed a set of metal ball bearings. Moreover, the chassis itself is quite old and worn out. I bought them used, only the chassis without other parts. I bought some parts. The body and model were tested in quite difficult terrain and without any sparing. Nothing broke, nothing came loose and everything is fine. That's why I can send my project to you. I hope that my project will be useful and will bring you a lot of joy. It would be nice if you added photos of the body printed and mounted on the chassis. My body is printed from PETG. I tried to make the parts printable without supports. I made assembly instructions. To connect the cabin, I recommend gluing nuts or using nuts with double-sided thread. I glued the nuts on mine. PL Zaprojektowana przeze mnie wytrzymała karoseria dla podwozia TAMIYA DT03. Karoseria składa się z wielu elementów, które pasują do siebie idealnie. Do złożenia karoserii trzeba użyć śrubek i nakrętek. Do złożenia karoserii należy w niektórych miejscach użyć kleju. Do złożenia niektórych elementów karoserii trzeba zrobić połączenia z pręta gwintowanego i tulejek M3X8. Zamontowanie karoserii na podwoziu TAMIYA DT03 nie wymaga niszczenia lub przerabiania oryginalnego podwozia. Tylko w jednym miejscu trzeba rozwiercić otwory do średnicy 3.1 mm. W tym miejscu można będzie po tej zmianie użyć zamiast wkrętów z oryginalnego zestawu, śrubki i nakrętki. Największym problemem podczas projektowania było nalezienie punktów bazowych oryginalnego podwozi i odczytanie właściwe krzywizn podwozia. Nie korzystałem z żadnych planów. Nie korzystałem z żadnych urządzeń, takich jak skanery. Używałem jedynie suwmiarki, linijki z podziałką w milimetrach. W trakcie projektowania kilkukrotnie wydrukowałem niektóre części i dokonałem przymiarki, następnie zrobiłem korekty. W skład projektu wchodzą części, które mogą być atrakcyjne jako odrębne elementy. Tylny spojler jest bardzo fajny i funkcjonalny. Jest też bardzo wytrzymały. Części wzmacniające sztywność oryginalnych z zestawu amortyzatorów, również mogą być przydatne. W dwóch miejscach wykorzystane są śrubki M3X25, tu można użyć i to nawet jest lepsze, śrubek M3X26, lub zmierzyć i dopasować / zrobić odpowiednie. Tak jest, bo chciałem już przetestować model, a nie mogłem kupić innych śrubek. Karoserię testowałem na standardowych częściach. Silnik podstawowy szczotkowy TAMIYA. Regulator podstawowy 60 A TAMIYA. Aparatura starego typu 27 MHz. Bateria NiMH dość stara 4000 mAh. Zamontowałem koła Carson. Zamontowałem zestaw łożysk kulkowych z metalu. Poza tym samo podwozie jest już dość stare i mocno zużyte. Kupiłem je jako używane, tylko podwozie bez innych części. Części dokupiłem. Karoseria i model przetestowany w dość trudnym terenie i bez oszczędzania. Nic nie pękło, nic się nie odkręciło i wszystko jest w porządku. Dlatego mogę wysłać mój projekt dla Was. Mam nadzieję, że mój projekt się przyda i przyniesie wiele radości z użytkowania. Fajnie jak dodacie zdjęcia wydrukowanej i zamontowanej na podwoziu karoserii. Moja karoseria wydrukowana jest z PETG. Starałem się, aby części można było drukować bez podpór. Zrobiłem instrukcję montażu. Dla połączenia kabiny z resztą, zalecam wkleić nakrętki, lub użyć nakrętek z gwintem dwustronnym. Ja u siebie nakrętki wkleiłem.

About the author:
adamwalczak
I have been dealing with technology from an early age. I am very happy with creating and solving difficult problems. I also deal with this topic professionally. I am a Specialist Mechanic and Electrician. I like to help. As a hobby, I develop other interests and combine various fields. Photography and graphics, RC modeling, automotive, shooting and military. Some of the graphics included in MyminiFactory can be purchased and downloaded in high definition from Adobe Stock for commercial use at the link: https://stock.adobe.com/pl/contributor/201480214/AWVW In 123RF you can download my other photos and graphics: https://pl.123rf.com/profile_awvw There are photos and graphics on various topics. I am open to various suggestions and ideas. I hope you enjoy my work and that it benefits you.

Reviews

This model have no reviews. Would you like to be the first to review? You need to print it first.