Boitier ventilé RAMPS Arduino LCD12864 / LCD12864 Arduino RAMPS case with fan

57 (likes)
9905 (views)
This product is available only if you have an account in My Mini Factory service
×
Color:

--- Videos --- Impression / Print : Assemblage / Assembly :   --- Français (English below) --- Voici la version avec ventilateur de mon boitier de commande d'imprimante 3D. A l’intérieur se logent : carte Arduino + RAMPS1.4 + écran LCD 12864 + deux ventilateurs 25x25 + un ventilateur 40x40. NB : Les pièces sont conçues pour être imprimées sans support matériel. L'assemblage compte trois pièces imprimées : - le corps principal - un panneau latéral - un capot pour l'écran LCD Quincaillerie : - 4 vis M3x20 - 2 vis M3x25 (ou M3x30) - 1 connecteur électrique femelle 2,1 x 5,5 mm   Préparation 1. Imprimez et nettoyez les trois pièces2. Supprimez les supports d'impression du panneau latéral : - Passage prise USB + passage carte SD - Emplacement connecteur électrique 3. Supprimez les supports du capot écran : - Passage bouton 4. Vérifiez que tout s’emboîte correctement Assemblage (Regardez la vidéo d'assemblage : lien en début d'article) 1. Fixez les ventilateurs 25x25 avec des vis M2,5x16. Une vis par ventilateur suffit.   2. Branchez les deux câbles de l'écran LCD sur la carte RAMPS uniquement.  3. Glissez les cartes Arduino et RAMPS préalablement câblées dans le boitier.  4. Attachez les câbles (et la gaine si vous en mettez une) en utilisant un collier plastique. 5. Glissez le ventilateur 40x40 dans son logement.  6. Montez le connecteur d'alimentation électrique femelle 2.1 x 5.5 sur le capot latéral  7. Branchez les câbles du ventilateur et de l'alimentation sur le bornier. 8. Mettez l'écran LCD en place 9. Placez son capot dessus et fixez-le avec une vis M3x20 en haut et une vis M3x25 en bas    10. Mettez le capot latéral en place et fixez-le à l'aide des trois vis M3x20 et la vis M3x25 restante qui se place au bas à gauche du capot d'écran. Et voilà, c'est fini ! Alors, heureux ? ;)   --- English --- Here is the version of my 3D printer control case with fan. Inside are housed : arduino card + RAMPS1.4 + LCD 12864 + two fans 25x25 + one fan 40x40. NB : Parts are designed to be printed without material support. The assembly consists of three printed parts : - the main body - a side panel - a LCD frame Hardware: - 4 screw M3x20 - 2 screw M3x25 ou M3x30 - 1 female electrical connector 2,1 x 5,5 mm   Prep 1. Print and clean the three parts2. Remove the printing supprts from the side panel : - USB plug and SD card passages - Electrical connector location 3. Remove the printing support from the LCD frame - Button passage 4 - Check that everything fits properly   Assembly (Watch the assembly video : link at the beginning of the article) 1. Fix fans 25 x 25 with M2,5x16 screws.One screw by fan is enough. 2. Connect the two cables of the LCD on the RAMPS board only. 3. Slide the Arduino and RAMPS cards previously wired into the case 4. Clamp the cables (and sheath) using a plastic tie 5. Slide the fan 40x40 into place. 6. Mount the female electrical power connector 2.1 x 5.5 on the side panel 7. Connect the fan and the power connector on the power terminal block 8. Put the LCD in place 9. Place the LCD frame and fix it with one M3x20 screws at the top and one M3x25 screw downstairs 10. Put the side cover and fasten it with three screws M3x20 and one screw M3x25 which is placed at the bottom left of the LCD frame.  and that's it! So, happy? ;)  

Author:
htaxil

Reviews

This model have no reviews. Would you like to be the first to review? You need to print it first.