Merry Christmas 2019 "Gift to All"

128 (likes)
11273 (views)
This product is available only if you have an account in My Mini Factory service
×
Color:

UPDATED 11/11/2023: (also if Myminifactory.com doesn't post the file because they have the slowest process, you can get the new base here: https://drive.google.com/file/d/10Lacy-8aoTAgpvfica2cFUVVQK-8GD/view?usp=sharing )I had some one point out that the base did not slice correctly in Cura.. Sorry, I don't test slice in each type of Slicer. I've used Slicer, then Prusa slicer and also Orca slicer. They do not give the errors Cura did with the v4 version of the base. I would recommend any of the Prusa slicer or Orca slicer. Cura is not as good. I did load Cura on to see the error the person was getting and found it. I had to dig deep to find the cause, which just ended up being an inverted face on one of the boolean's. Which Prusa slicer had no issue with, but Cura, well , I'm still not impressed with it yet.. and it proved to not handle a complex design as well as Prusa slicer. I designed this in Blender 2.80 as a gift for all for 2019 (last years was https://www.myminifactory.com/object/3d-print-merry-christmas-gift-to-all-79386 , solar version https://www.myminifactory.com/object/3d-print-merry-christmas-solar-version-gift-to-all-79488 ). I listened to what people suggested and started with a circle in Blender and created this from the ground up with a moving train. It is designed for as many printers as I could, its a 200mmx200mm base. I created it looking at every part and tree, not needing any support. I wanted to make this as simple as possible even for beginners. It is one very easy print. This version works and is complete and tested. I put in hollow tubes in many locations so you can put electronics how ever you prefer, inside, outside. Lights in buildings or Christmas tree. Update: 11-6-19  Gear04 is a tad smaller for printers that are less accurate.  Schematics for just motor set up:https://easyeda.com/shermluge/microwave-motion-and-on-off-circuitEven with adding LED's with 1k - 2k resisters makes it so with motor on I only pull 40ma through the Mosfet. Parts and were to get them (very low cost) motor:https://www.ebay.com/itm/New-Micro-Gear-Box-Speed-Reduction-Motor-Electric-Geared-Motor-6V-50-to-300RPM/123598737052?ssPageName=STRK%3AMEBIDX%3AIT&trksid=p2057872.m2749.l2649https://www.amazon.com/Yosoo-Reduction-Engine-Gearbox-Replacement/dp/B01BBSXDGW/ref=sr16?keywords=Micro+Gear+Box+Speed+Reduction+Motor+Electric+Geared+Motor+6V+50+to+300RPM&qid=1563916058&s=gateway&sr=8-6 motion sensor:https://www.aliexpress.com/item/32816449998.html?spm=a2g0s.9042311.0.0.27424c4djnvpJhhttps://www.amazon.com/Maxmoral-RCWL-0516-Microwave-Induction-Intelligent/dp/B07S221PB4/ref=sr1_6?keywords=rcwl0516+microwave+radar+sensor&qid=1563916285&s=gateway&sr=8-6https://www.ebay.com/itm/RCWL-0516-Microwave-Radar-Sensor-Module-Human-Body-Induction-Switch-Module-CA/142383691574?hash=item2126bab736:g:vusAAOSwaEhZGYEG electronic switch:2N7000 mosfet10k resistor220 resistor 100nf capacitor for motion sensor if used.. Put on C-TM - jumper on microwave motion to change from 2 seconds to 30 seconds. For 10 seconds use a 22nf capacitor. To adjust distance, you can put a 680k ohm resistor on R-GN to change the range from 7 meters to about 3 meters. Assembly video:https://www.youtube.com/watch?v=XLeWQsXkJHY Merry Christmas and enjoy Sherm More of my designs that are free:https://www.thingiverse.com/shermluge/designs https://www.myminifactory.com/users/shermluge   And Thank you 3d Printing Professor: https://www.youtube.com/watch?v=JGYb9PpIFSA  

About the author:
shermluge
Electronic engineering Art 3d printing Designer and Maker Donate: paypal.me/shermluge

Reviews

This model have no reviews. Would you like to be the first to review? You need to print it first.