Athena Lemnia at The Royal Cast Collection, Copenhagen

12 (likes)
8476 (views)
This product is available only if you have an account in My Mini Factory service
×
Color:

The Lemnian Athena, or Athena Lemnia, was a classical Greek statue of the goddess Athena. According to Pausanias (1.28.2), the original bronze was created by Phidias circa 450-440 BCE, for Athenians living on Lemnos to dedicate on the Acropolis inAthens, Greece. It is unclear whether any copies remain. In 1891 Adolf Furtwängler reconstructed two virtually identical, Roman marble statues which he claimed as copies of the original, and identified two Roman marble copies of the head alone. These completed statues were recreated by joining a poorly preserved marble head (Dresden) and a plaster cast of a similar Roman marble head, from the collection of Pelagio Palagi (Bologna), to a pair of identical bodies in Dresden. Both reconstructions and attributions have been disputed; see below. The sculptures concerned are: Two full reconstructions (A and B) in the Staatliche Museum, Albertinum, Dresden, with bodies purchased in 1728 from the Chigi collection, Rome, Italy. The Palagi head at the Archaeological Museum of Bologna, Italy. A further head of this type, found at Pozzuoli is conserved in the Archaeological Museum of the Campi Phlegraei. As reconstructed, the completed statues are pastiches of two Roman marbles, one for the head and the other for the body. Athena wears an unusual, cross-slung aegis decorated with the Gorgon's head. She is bare-headed, without shield, holding her helmet out in her extended right hand, and with her left grasping her spear near the top of the shaft. Furtwängler's identification of the original Athena Lemnia with the Dresden statues and Palagi head was based upon study of an engraved gem and by interpretation of the following passages from Pausanias, Lucian, and Himerios: Pausanias 1.28.2: [On the Acropolis] there are also two other dedications, a statue of Pericles, son of Xanthippos, and the most worth seeing of the works of Phidias, the statue of Athena called the Lemnian after those who dedicated it. Lucian, Imagines 4 and 6: (4) Lykinos: "Of all the works of Phidias, which one do you praise most highly?"Polystratos: "Which if not the Lemnia, on which he thought fit to inscribe his name? Or the Amazon leaning on her spear?...(6) From the Knidia the sculptor [of Panthea] will take only the head, ... allowing the hair, forehead, and that lovely brow-line to remain just as Praxiteles made them, and the liquid yet clear and winsome gaze of the eyes shall stay as Praxiteles conceived it. But he will take the curve of the cheeks and the fore part of the face from Alkamenes' [Aphrodite] in the Gardens, plus her hands, graceful wrists, and supple, tapering fingers. But the facial contour, its softness, and her well-proportioned nose will be supplied by the Lemnian Athena of Phidias, who will also furnish the meeting of the lips and the neck, taken from the Amazon." Himerios, Oratio 68.4 (Colonna): Phidias did not always make images of Zeus, nor did he always cast Athena armed into bronze, but turned his art to the other gods and adorned the Maiden's cheeks with a rosy blush, so that in place of her helmet this should cover the goddess's beauty. Furtwängler's logic has been disputed. "Hartswick has shown that the Palagi head in Bologna cannot have come from Dresden statue B, that the gems Furtwängler employed could be post-antique, and that the sources are impossibly vague." (Stewart) Some of Hartwick's own conclusions have been disputed in turn, i.e., that the head of Dresden A is alien and the entire Palagi type is Hadrianic. Stewart remarks, "So while the type remains intact and looks Phidian, Furtwängler's further hypotheses concerning its identity and date (451-448) remain unproven." Athena Lemnia (reconstruction), Phidias, Greek, ca 440 B.C., Dresden and Bologna, The Royal Cast collection (Copenhagen, Denmark). Made with Memento Beta (now Remake) from Autodesk.

About the author:
geoffrey.marchal
EN: Scientist passionate of computer graphic and science simulation and visualization. I started doing computer grqphic at 19, in 1993. Passing from POV-RAY to LightWave, Houdini, 3DStudio, 3DS Max, Blender. In 2014, I have started 3D scanning with first a Kinect from Microsoft and afterward moved to photogrammetry. Photogrammetry is more flexible and I use mainly 123D Catch and Memento beta, both from Autodesk. In 2015, I started 3D printing with a Solidoodle Press. FR: Scientifique travaillant dans une universite. Je suis passionne par les images de synthese depuis 1993 commencant avec POV-RAY, passant par LightWave et 3DSMax. Depuis 2009, je suis exclusivement sur Blender. En 2014, j' ai decouvert le scan 3D via la Kinect et tres vite j'ai change pour la photogrammetrie. La photogrammetrie permet de faire des scan 3D plus facilement avec un simple appareil photo. J' utilise principalement 123D Catch et Memento beta, les deux produit par Autodesk. En 2015, j'ai debute avec l'impression 3D avec une Solidoodle Press

Reviews

This model have no reviews. Would you like to be the first to review? You need to print it first.